Jesteśmy do Twojej dyspozycji od Poniedziałku do Piątku w godzinach: 9:00 - 18:00

Ultimate Nano Coat v2

Krótki opis

Max Protect UNC-v2 powłoka bardzo trwała a zarazem prosta w aplikacji, daje bardzo lustrzany połysk.

W magazynie

Nazwa produktu Cena Ilość
Ultimate Nano Coat v2 30ml
349,00 zł
LUB

Szczegóły

Max Protect UNC-v2 powłoka bardzo trwała a zarazem prosta w aplikacji, daje bardzo lustrzany połysk.


•Trwałość do dwóch lat
•Bardzo wysoka odporność na ataki chemiczne (ptasie odchody, kwaśne deszcze, silne detergenty itp.)
•Ochrona przed UV
•Odporność na temperaturę -60C , +1200C
•Bardzo skuteczny jako samodzielny produkt, ale dla maksymalnej trwałości, ochrony i lustrzanego połysku
zalecamy, aby stosować go na Max Protect UNC-v1
•Przywraca plastikowym elementom oryginalny kolor i pozostawia piękny satynowy wygląd
•Pojemność 30 ml.

Best Value Nano Glass Coating for Professionals!

>>> Download Instructions <<<

Powierzchnia musi być oczyszczona i odtłuszczona, sucha z dala od bezpośredniego światła słonecznego.
W temperaturze poniżej 25C pozostaw powłokę na około 3 min. przed spolerowaniem.
Zalecana jest dobra wentylacja i noszenie ochronnej odzieży roboczej (rękawice, okulary, maska itp.)

ENG

UNC v2 can be applied as a single layer product, or as an additional layer to UNC v1. A single layer application is by far the best solution for busy professionals, but if you are a die-hard DIY enthusiast and are looking for something little extra in car paint protection, we recommend to apply UNC v2 over a layer of pre-cured UNC v1.

For best results, a machine polish is recommended before UNC v2 application. In case of a brand new car or car with excellent paint condition, we recommend at least a clay bar treatment or hand polish. In many cases, a mild machine polish will be quicker and less painful than polishing by hand.

If you are getting your new car straight from the dealership and are looking to get this product applied, it would be very helpful to know what product the dealership has applied on the paintwork to see what steps are necessary to prepare the paintwork for UNC v2 application. 

We recommend using polishing compounds with minimum or no oils & wax in content. Polishing compounds with waxes and high oil content should be avoided. 

Use Panel Wipe or IPA to degrease paintwork before UNC v2 application.

Important:

It is very important to have good lighting in the place of application! In dim light you might not spot smears left behind and removing them later will be a lot more difficult. Do not use in direct sun. Also, good ventilation and wearing protective work wear (gloves, googles, mask, etc.) is recommended.

Please make sure you have the following before UNC v2 application:

1. Panel Wipe – not supplied
2. Ultimate Nano Coat v2
3. Silk Coat – not supplied
5. Applicator Sponge – not supplied
6. Microfiber Towels – not supplied

Stage 1: UNC v2 Application:

Attention: UNC v2 flashes off much quicker than UNC v1. To ensure you have enough time to remove it, try it on a smaller panel first, before applying on bigger panels like bonnet or roof.

1. Open UNC v2 bottle and put the applicator sponge on top and shake it once. Move the sponge a bit and shake it again. Do it for 3-4 times till the sponge is slightly wet (not soaked!).
2. Put the sponge on the surface and apply the coating with short and quick movements. Do not apply in circular movements, keep it in a straight line. Keep applying till the whole panel is covered. 
3. Once a large panel is covered (roof, bonnet), remove the coating immediately with a fresh microfiber cloth/ towel.
4. For smaller panels like wings and other small panels we recommend waiting for 30-60 seconds before removal.
5. Apply v2 on one panel at a time. Take extra care to look for marks/ smears left behind as removing them later will be more difficult.
6. Use 2 microfiber towels/cloths for excess removal.

Stage 2: Silk Coat Application:

Silk Coat is a protective layer for the coating while it’s curing. The maximum curing time for UNC v2 is 6 hours and if you need to drive the car in that period, Silk Coat will protect the coating in all weather conditions. It also works very well as a top-up for the hydrophobic properties of the coating. We recommend applying Silk Coat for maintenance 2-4 times a year, or as often as you like. It’s super easy to apply and adds a very smooth feel to the surface. 

1. Shake bottle well and spray in fine mist on few panels at a time. No need to cover the surface completely. 7-9 sprays per sqm are enough. 
2. Remove by wiping panel gently with a fresh microfiber towel straight after application till a super smooth and clear finish is achieved.

Tips:

1. Always use new microfiber towels/cloths
2. The coating crystallizes around the bottle necks, so take extra care when opening bottles for the first time.
3. Pay attention: once the sponge is dried, the liquid get crystalized and the sponge couldn’t be re-used. 
5. Remember not to mix microfiber towels between Stage 1 & Stage 2.
6. Use Silk Coat for maintenance – super easy to apply!

Napisz własną recenzję

Tylko zarejestrowani kiienci mogą pisać opinie. Proszę zalogować się lub zarejestrować