Jesteśmy do Twojej dyspozycji od Poniedziałku do Piątku w godzinach: 9:00 - 18:00

Ultimate Nano Coat v1

Krótki opis

Max Protect UNC-v1 jest to prawdopodobnie najłatwiejsza w aplikacji nano powłoka na rynku, która daje lustrzany połysk.

W magazynie

Nazwa produktu Cena Ilość
Ultimate Nano Coat v1 30ml
349,00 zł
LUB

Szczegóły

Max Protect Ultimate Nano Coat v1

Max Protect UNC-v1 jest to prawdopodobnie najłatwiejsza w aplikacji nano powłoka na rynku, która daje lustrzany połysk. Można ją swobodnie warstwować.


•Trwałość około jednego roku
•Głęboki połysk
•Wysoka odporność na ataki chemiczne (ptasie odchody, kwaśne deszcze, silne detergenty itp.)
•Ochrona przed UV
•Odporność na temperaturę -60C, +1200C
•Może być stosowana w wielu warstwach (zalecany czas oczekiwania między warstwami wynosi 55-150 min. w
zależności od temperatury
•Dla poprawy wyglądu, trwałości i lustrzanego odbicia można na powłokę UNC-v1 nołożyć UNC-v2 lub UNC-R.
•Przywraca plastikowym elementom oryginalny kolor
•Pojemność 30 ml.

>>> Download Instructions <<<

Powierzchnia musi być oczyszczona i odtłuszczona, sucha z dala od bezpośredniego światła słonecznego. Aplikujemy całe elementy, poniżej 25C pozostawiamy powłokę na 10-20 min. przed spolerowaniem. Najlepiej użyć dwóch fibr, pierwszą ściągamy nadmiar, drugą polerujemy aż usuniemy wszystkie smugi. Zalecana jest dobra wentylacja i noszenie ochronnej odzieży roboczej (rękawice, okulary, maska itp.)

ENG:

For best results, paintwork should be machine polished before UNC v1 Application. A fine polish is all that is necessary to prepare the surface for coating application. In case of a brand new car, or a car with paintwork in excellent condition, we recommend to polish by hand, or perform a very mild, final stage machine polish. Degreasing with Panel Wipe is recommended for best results, if not available, IPA or similar cleaners will do the job too.

UNC v1 can be applied in a single layer or in multiple layers. It is often used as a base layer before UNC v2 or UNC-R application, to acchieve extended durability.

We recommend using polishing compounds with minimum or no oils in content. Polishing compounds with waxes and high oil content should be avoided.

Important: It is very important to have good lighting in the place of application! In dim light you might not spot smears left behind and removing them later will be a lot more difficult. 

Good ventilation is a must to have and appropriate safety wear (Gloves, Glasses, Mask, etc.) should be worn.

Please make sure you have the following before UNC v1 application:

1. Panel Wipe – not supplied
2. Ultimate Nano Coat v1
3. Silk Coat – not supplied
5. Applicator Sponge – not supplied
6. Microfiber Towels – not supplied

Stage 1: UNC v1 Application:

Once again make sure the surface is cleaned with panel wipe before coating application. Clean the surface thoroughly with a fresh microfiber towel and make sure there are no visible marks on the paint before commencing the coating application. If the applicator sponge is making a squeaking sound when applying the first stage of the coating – that’s a good sign the paint is cleaned well. If it’s sliding easily, you might need to re-clean it again with Panel wiper or PD.

1. Open the UNC v1 bottle and put the applicator sponge on top and shake it once. Move the sponge a bit and shake it again. Do it for 3-4 times till the sponge is slightly wet, but not soaked).
2. Put the sponge on the surface and apply the coating with short and quick movements.
3. Do not apply in circular movements. Keep applying till the whole panel is covered.
3. Below temperatures of +25c leave the coating for 5-10 minutes before removal.
4. Remove the coating with a microfiber towel cloth till smear free. We recommend using 2 towels/cloths for excess coating removal.

* We recommend applying and wiping off the v1 coating at this order:
Roof, bonnet, right side, baggage, left side, bumpers and other painted surfaces.
Apply each section, wipe off thoroughly and apply to the next.

Stage 2: Silk Coat:

Silk Coat is protective layer for the coating while it’s curing. The maximum curing time is 48 hours and if you need to drive the car in that period, Silk Coat will protect the coating in all weather conditions. It also works very well as to top-up for the hydrophobic properties of the coating. We recommend applying Silk Coat for maintenance 2-4 times a year, or as often as you like. It’s super easy to apply and adds a very smooth feel to the surface.

Silk Coat Application:

1. Shake bottle well and spray in fine mist on few panels at a time. No need to cover the surface completely. 7-9 sprays per sqm are enough.
2. Remove by wiping panel gently with a fresh microfiber towel immediately after application till all white marks disappear.

Tips:

1. Always use new microfiber towels/cloths
2. The coating crystallizes around the bottle necks, so take extra care when opening bottles for the first time.
3. Pay attention: once the sponge is dried, the liquid get crystalized and the sponge couldn’t be re-used.
5. Remember not to mix microfiber towels between Stage 1 & Stage 2.
6. Use Silk Coat for maintenance – super easy to apply!

 

Napisz własną recenzję

Tylko zarejestrowani kiienci mogą pisać opinie. Proszę zalogować się lub zarejestrować

Mogą cię również zainteresować następujące produkty